SIEMENS SIPLUS LOGO! – SIPLUS LOGO!Power

SIPLUS extreme products are based on SIMATIC standard products. The contents listed here were adopted from the respective standard products. SIPLUS extreme-specific information was added.

The SIPLUS LOGO!Power supplies are optimally matched in design and functionality to the SIPLUS LOGO! logic modules; with wide-range input 85 V to 264 V AC and option for installing in built-in miniature distribution boards, they can be used universally in the low-end performance range as well as in an extended operating temperature range of -25 to +70 °C.

SIPLUS LOGO!Power
Product No. / Product DescriptionListprice / Your price
6AG1331-1SH03-7AA0
SIPLUS LOGO! POWER 24V 1.3A FOR MEDIAL STRESS -25 … +70 DEGREES C BASED-ON 6EP1331-1SH03 . STABILIZED POWER SUPPLY INPUT: V/1.3 A DC
6AG1332-1SH43-7AA0
SIPLUS LOGO! POWER 24V 2,5A FOR MEDIAL STRESS -40…+70 DEGREE C BASED-ON 6EP1332-1SH43. STABILIZED POWER SUPPLY INPUT: V/2.5 A DC
6AG1332-1SH52-7AA0
SIPLUS LOGO! POWER 24V 4 A FOR MEDIAL STRESS -40…+70 DEGR C BASED-ON 6EP1332-1SH52 .STABILIZED POWER SUPPLY INPUT: AC (110-300 V DC) OUTPUT: 24 V/

SIPLUS LOGO!Power 1.3 A

Article No.

6AG1 331-1SH03-7AA0

Article No. based on

6EP1 331-1SH03

Ambient temperature range

-25 °C … +70 °C

Conformal coating

Coating of the printed circuit boards and the electronic components

Technical specifications

The technical data of the standard product applies except for the ambient conditions.

Ambient conditions

Relative humidity

100%, condensation/frost permissible. No commissioning in bedewed state.

Biologically active substances, compliance with EN 60721-3-3

Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!

Chemically active substances, compliance with EN 60721-3-3

Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation!

Mechanically active substances, compliance with EN 60721-3-3

Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation!

Air pressure (depending on the highest positive temperature range specified)

1 080 … 795 hPa (-1 000 … +2 000 m)
see ambient temperature range

795 … 658 hPa (+2000 … +3500 m)
derating 10 K

658 … 540 hPa (+3500 … +5000 m)
derating 20 K

Technical specifications

Article number

6AG1331-1SH03-7AA0

6AG1332-1SH43-7AA0

6AG1332-1SH52-7AA0

Product

SIPLUS LOGO!Power

SIPLUS LOGO!Power

SIPLUS LOGO!Power

Power supply, type

24 V/1.3 A

24 V/2.5 A

24 V/4 A

Input

Input

1-phase AC or DC

1-phase AC or DC

1-phase AC or DC

Rated voltage value Vin rated

100 … 240 V

100 … 240 V

100 … 240 V

Voltage range AC

85 … 264 V

85 … 264 V

85 … 264 V

Input voltage

  • ● at DC

110 … 300 V

110 … 300 V

110 … 300 V

Wide-range input

Yes

Yes

Yes

Overvoltage resistance

2.3 × Vin rated, 1.3 ms

2.3 × Vin rated, 1.3 ms

2.3 × Vin rated, 1.3 ms

Mains buffering at Iout rated, min.

40 ms; at Vin = 187 V

40 ms; at Vin = 187 V

40 ms; at Vin = 187 V

Rated line frequency 1

50 Hz

50 Hz

50 Hz

Rated line frequency 2

60 Hz

60 Hz

60 Hz

Rated line range

47 … 63 Hz

47 … 63 Hz

47 … 63 Hz

Input current

  • ● at rated input voltage 120 V

0.7 A

1.22 A

1.95 A

  • ● at rated input voltage 230 V

0.35 A

0.66 A

0.97 A

Switch-on current limiting (+25 °C), max.

25 A

46 A

30 A

I²t, max.

0.8 A²·s

3 A²·s

2.5 A²·s

Built-in incoming fuse

internal

internal

internal

Protection in the mains power input (IEC 898)

Recommended miniature circuit breaker: from 6 A characteristic B or from 2 A characteristic C

Recommended miniature circuit breaker: from 10 A characteristic B or from 6 A characteristic C

Recommended miniature circuit breaker: from 10 A characteristic B or from 6 A characteristic C

Output

Output

Controlled, isolated DC voltage

Controlled, isolated DC voltage

Controlled, isolated DC voltage

Rated voltage Vout DC

24 V

24 V

24 V

Total tolerance, static ±

3 %

3 %

3 %

Static mains compensation, approx.

0.1 %

0.1 %

0.1 %

Static load balancing, approx.

1.5 %

1.5 %

1.5 %

Residual ripple peak-peak, max.

200 mV

200 mV

200 mV

Residual ripple peak-peak, typ.

10 mV

10 mV

30 mV

Spikes peak-peak, max. (bandwidth: 20 MHz)

300 mV

300 mV

300 mV

Spikes peak-peak, typ. (bandwidth: 20 MHz)

20 mV

50 mV

60 mV

Adjustment range

22.2 … 26.4 V

22.2 … 26.4 V

22.2 … 26.4 V

Product function Output voltage adjustable

Yes

Yes

Yes

Output voltage setting

via potentiometer

via potentiometer

via potentiometer

Status display

Green LED for output voltage OK

Green LED for output voltage OK

Green LED for output voltage OK

On/off behavior

No overshoot of Vout (soft start)

No overshoot of Vout (soft start)

No overshoot of Vout (soft start)

Startup delay, max.

0.5 s

0.5 s

0.5 s

Voltage rise, typ.

15 ms

10 ms

15 ms

Rated current value Iout rated

1.3 A

2.5 A

4 A

Current range

0 … 1.3 A

0 … 2.5 A

0 … 4 A

  • ● Note

+55 … +70 °C: Derating 2%/K

+55 … +70 °C: Derating 2%/K

+55 … +70 °C: Derating 2%/K

Supplied active power typical

30 W

60 W

96 W

Parallel switching for enhanced performance

Yes

Yes

Yes

Numbers of parallel switchable units for enhanced performance

2

2

2

Efficiency

Efficiency at Vout rated, Iout rated, approx.

85 %

88 %

89 %

Power loss at Vout rated, Iout rated, approx.

6 W

8 W

12 W

Closed-loop control

Dynamic mains compensation (Vin rated ±15 %), max.

0.2 %

0.2 %

0.2 %

Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.

1 %

2 %

1.5 %

Load step setting time 10 to 90%, typ.

1 ms

1 ms

1 ms

Load step setting time 90 to 10%, typ.

1 ms

1 ms

1 ms

Protection and monitoring

Output overvoltage protection

Yes, according to EN 60950-1

Yes, according to EN 60950-1

Yes, according to EN 60950-1

Current limitation, typ.

1.7 A

3.3 A

5.2 A

Property of the output Short-circuit proof

Yes

Yes

Yes

Short-circuit protection

Constant current characteristic

Constant current characteristic

Constant current characteristic

Enduring short circuit current RMS value

  • ● maximum

2.4 A

4.8 A

7.9 A

Overload/short-circuit indicator

Safety

Primary/secondary isolation

Yes

Yes

Yes

Galvanic isolation

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178

Protection class

Class II (without protective conductor)

Class II (without protective conductor)

Class II (without protective conductor)

CE mark

Yes

Yes

Yes

Degree of protection (EN 60529)

IP20

IP20

IP20

EMC

Emitted interference

EN 55022 Class B

EN 55022 Class B

EN 55022 Class B

Supply harmonics limitation

not applicable

not applicable

EN 61000-3-2

Noise immunity

EN 61000-6-2

EN 61000-6-2

EN 61000-6-2

Operating data

Ambient temperature

  • ● during operation

-40 … +70 °C

-40 … +70 °C

-40 … +70 °C

  • — Note

with natural convection

with natural convection

with natural convection

  • ● during transport

-40 … +85 °C

-40 … +85 °C

-40 … +85 °C

  • ● during storage

-40 … +85 °C

-40 … +85 °C

-40 … +85 °C

Ambient condition relating to ambient temperature – air pressure – installation altitude

Tmin … Tmax at 1080 hPa … 795 hPa (-1000 m … +2000 m); Tmin … (Tmax – 10K) at 795 hPa … 658 hPa (+2000 m … +3500 m); Tmin … (Tmax – 20K) at 658 hPa … 540 hPa (+3500 m … +5000 m)

Tmin … Tmax at 1080 hPa … 795 hPa (-1000 m … +2000 m); Tmin … (Tmax – 10K) at 795 hPa … 658 hPa (+2000 m … +3500 m); Tmin … (Tmax – 20K) at 658 hPa … 540 hPa (+3500 m … +5000 m)

Tmin … Tmax at 1080 hPa … 795 hPa (-1000 m … +2000 m); Tmin … (Tmax – 10K) at 795 hPa … 658 hPa (+2000 m … +3500 m); Tmin … (Tmax – 20K) at 658 hPa … 540 hPa (+3500 m … +5000 m)

Relative humidity with condensation maximum

100 %; Relative humidity, incl. condensation/frost permitted (no commissioning under condensation conditions)

100 %; Relative humidity, incl. condensation/frost permitted (no commissioning under condensation conditions)

100 %; Relative humidity, incl. condensation/frost permitted (no commissioning under condensation conditions)

Resistance to biologically active substances conformity acc. to EN 60721-3-3

Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation!

Resistance to chemically active substances conformity acc. to EN 60721-3-3

Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!

Resistance to mechanically active substances conformity acc. to EN 60721-3-3

Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!

Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation!

Mechanics

Connection technology

screw-type terminals

screw-type terminals

screw-type terminals

Connections

  • ● Supply input

L, N: 1 screw terminal each for 0.5 … 2.5 mm2 single-core/finely stranded

L, N: 1 screw terminal each for 0.5 … 2.5 mm2 single-core/finely stranded

L, N: 1 screw terminal each for 0.5 … 2.5 mm2 single-core/finely stranded

  • ● Output

+, -: 2 screw terminals each for 0.5 … 2.5 mm²

+, -: 2 screw terminals each for 0.5 … 2.5 mm²

+, -: 2 screw terminals each for 0.5 … 2.5 mm²

  • ● Auxiliary

Width of the enclosure

54 mm

72 mm

90 mm

Height of the enclosure

90 mm

90 mm

90 mm

Depth of the enclosure

55 mm

55 mm

55 mm

Required spacing

  • ● top

20 mm

20 mm

20 mm

  • ● bottom

20 mm

20 mm

20 mm

  • ● left

0 mm

0 mm

0 mm

  • ● right

0 mm

0 mm

0 mm

Weight, approx.

0.17 kg

0.25 kg

0.34 kg

Product feature of the enclosure housing for side-by-side mounting

Yes

Yes

Yes

Installation

Snaps onto DIN rail EN 60715 35×7.5/15

Snaps onto DIN rail EN 60715 35×7.5/15

Snaps onto DIN rail EN 60715 35×7.5/15

Other information

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

Popular Products Series

GE QuickPanel family of Human Machine Interfaces Ge Fanuc HMI

AoteWell Sell all models of the popular GE IP QuickPanel family…

Mitsubishi F740 Series Frequency Inverter

The FR-F700 Series was launched in 2004 as the successor to the FR-F500 Series VFD. With growing market demands for energy saving inverters in building automation, water processing and HVAC industries, the FR-F700 was able to exceed power-saving expectations in fan and pump applications by incorporating “OEC” (optimum excitation control) which combined maximum drive utilization with minimal power consumption.

Siemens PLC spare part 6AV 6DD 6SN 6ES5 6ES7

Main supply Siemens 6ES7 6AV6 6AV3 6SE7 Spare parts...

Allen-Bradley 6176M Standard Industrial Monitors

Allen-Bradley 6176M Standard Industrial Monitors
6176M Standard Monitors are flat panel industrial color monitors for use in less demanding environments. All Standard Monitors have USB and RS232 touch screen inputs, DVI and VGA video inputs, and an On Screen Display (OSD) that enables image rotation, color pallet changes, and push button auto reset.

Allen-Bradley 6186M Performance Monitors

Simatic S7-200 Smart PLC

SIEMNES SIMATIC S7-200 Smart, newly launched micro PLC Product, is designed to suit the needs of developing markets that are under constant pressure due to price and demands for continuous performance. Providing an excellent performance – to – price ratio, SIMATIC S7 200 SMART when combined with other smart drive products from Siemens helps in building a cost effective yet efficient automation Solution.

ACS800-104/-104LC – inverter module

ACS800-04 – single drive modules

Load more