Industry automation over 20 year

[email protected]

24/7 Customer Support

Mon - Fri: 8:30 - 21:00

Online Store always open

YOKOGAWA PH450 4-WIRE PH/ORP ANALYZER PH450

YOKOGAWA PH450

The PH450 pH analyzer provides the best accuracy in the industry, featuring an advanced temperature compensation functionality, preloaded calibration standards, stability checks, and online sensor and analyzer diagnostics to provide verifiable results.

This four-wire, multivariable analyzer combines pH with temperature and ORP (Redox) measurement, all of which can be utilized through the different output functions: two mA current outputs, four independent SPDT contact outputs, and HART. Dynamic sensor checking and wash cycle functions assure trouble free and accurate analysis with minimum maintenance.

Series Name: YOKOGAWA PH450
Share on facebook
Share on google
Share on twitter
Share on linkedin
Product Keywords: YOKOGAWA PH450

PH450G-A(D)-A
The PH450 is supplied with terminals suitable for the connection of finished wires in the size range of 0.13 to 2.5 sq.mm. ( 26 to 14 AWG).
The cable glands supplied will form a tight seal on cables with an outside diameter of 6 to 12 mm (0.24 to 0.47 inches). Unused cable entry holes must be sealed with cable glands including the close up plugs supplied.

PH450G-A(D)-U
The PH450 is supplied with terminals suitable for the connection of finished wires in the size range of 14- 26 AWG. The cable entry holes are sealed with FM certified plugs. Prior to cable entry the plugs can be removed with allen key size 3/8” The cable conduit fittings can be mounted in the holes of the housing as required. The cable glands supplied with the unit will give a tight seal on cables with outside diameter of 0.24 to 0.47 inches.

GENERAL SPECIFICATIONS OF EXAXT PH450G

A) Inputs specs : Dual high impedance input (≥ 1012Ω)
(under referance conditions)
B) Input ranges
pH : -2 to 16 pH
ORP : -1500 to 1500 mV
rH : 0 to 100 rH
Temperature
– Pt1000 : -30 to 140ºC
– Pt100 : -30 to 140ºC
– 350Ω (DKK) : -30 to 140ºC
– 5k1 : -30 to 140ºC
– 6k8 : -30 to 140ºC
– PTC10k : -30 to 140ºC
– NTC 8k55 : -10 to 120ºC
– 3kBalco : -30 to 140ºC
C) Accuracy
pH input : ≤ 0.01 pH
ORP input : ≤ 1 mV
Temperature : ≤ 0.3 ºC (≤ 0.4 ºC for Pt100)
Step response : < 4 sec for 90% (pH 7 – pH 4) Note on performance specifications The following tolerance is added to above performance. mA output tolerance: ±0.02 mA of “4-20 mA“ D) Transmission signals General : Two isolated outputs of 4-20 mA. DC with common negative. Maximum load 600Ω. Bi-directional HART® digital communication, superimposed on mA1 (4-20 mA) signal Output functions : Linear or Non linear (21-step table) output for pH, temperature, ORP or rH Control function : PID control Burnout function : Burn up (21.0 mA) or burn down (3.6 mA) to signal failure acc. NAMUR NE43 Adjustable damping. Expire time Hold : The mA-outputs are frozen to the last/fixed value during calibration/ commissioning E) Contact outputs General : Four SPDT relay contacts with display indicators Switch capacity : Maximum values 100 VA, 250 VAC, 5 Amps.(*) Maximum values 50 Watts, 250 VDC, 5 Amps.(*) Status : High/Low process alarms, selected from pH, ORP, rH and temperature Configurable delay time and hysteresis Failure annunciation Control function : On/Off, PID duty cycle or pulsed frequency control Wash : Contact can be used to start manual- or interval time wash cycles Hold : Contact can be used to signal the Hold situation. Fail : Contact S4 is programmed as fail-safe contact (*) Note: When contact output current is more than 4 Amps. ambient temperature should be less than 40ºC. F) Contact input : Remote wash cycle start. G) Temperature compensation Function : Automatic or manual Compensation to Nernst equation Process compensation by configurable temperature coefficient, NEN6411 for water or strong acids/bases or programmable matrix H) Calibration : Semi-automatic 1 or 2 point calibration using pre-configured NIST, US, DIN buffer tables 4, 7 & 9, or with user defined buffer tables, with automatic stability check Manual adjustment to grab sample I) Logbook : Software record of important events and diagnostic data readily available in the display or through HART®. J) Display : Graphical Quarter VGA (320 x 240 pixels) LCD with LED backlight and touchscreen. Plain language messages in English, German, French, Spanish, Italian, Swedish ,Portuguese and Japanese. K) Shipping details Package size : 290 x 300 x 290 mm (L x W x D) (11.5 x 11.8 x 11.5 inch) Package weight : app. 2.5 kg (5.5 lbs) Converter weight : app. 1.5 kg L) Housing : Cast aluminum housing with chemically resistant coating; Polycarbonate cover with Polycarbonate flexible window : Protection IP66 / NEMA 4X / CSA Type 3S Colour : Silver grey PH450G-A(D)-A : IP66 cable glands are supplied with the unit PH450G-A(D)-U : NEMA 4X close up plugs are mounted in the unused cable entry holes and can be replaced by conduit fittings as required Pipe, Panel or Wall mounting using optional hardware Optional conduit adapter G1/2, 1/2NPT or M20 female M) Power supply PH450G-A : Ratings; 100-240 V AC Acceptable range; 90 to 264 V AC Ratings; 50/60 Hz Acceptable range; 50 Hz ±5%, 60 Hz ±5% Power Consumption; 15 VA PH450G-D : Ratings; 12-24 V DC Acceptable range; 10.8 to 26.4 V DC Power Consumption; 10 W N) Safety and EMC conforming standards , Safety : EN 61010-1 CSA C22.2 No.61010-1 UL 61010-1 FM3611 Class I, Div.2, Group ABCD,T6 for Ta -20 to 55ºC EMC : EN 61326-1 Class A, Table 2 (For use in industrial locations) EN 61326-2-3 EN 61000-3-2 Class A EN 61000-3-3 Korea Electromagnetic Conformity Standard Installation altitude: 2000 m or less Category based on IEC 61010: II (Note) Pollution degree based on IEC 61010: 2 (Note) Note: Installation category, called over-voltage category, specifies impulse withstand voltage. Category II is for electrical equipment. Pollution degree indicates the degree of existence of solid, liquid, gas or other inclusions which may reduce dielectric strength. Degree 2 is the normal indoor environment.

Additional Features

  • Capable of analyzing pH, ORP or rH and Temperature measurements at the same time with the same sensor
  • Full PID control possible for both acid and alkaline addition simultaneously
  • Dual High Impedance Capability, allowing for Differential pH/ORP measurements
  • Enhanced diagnostics, process trending graphics and on-screen logbooks for data storage
  • Two mA-outputs and four SPDT relay contacts with display indicators
  • Hart® Communications
  • FM Class 1, Div.2, Group ABCD, T6 for Ta-20 to 55°C
  • IP66/NEMA4X 1/2 DIN enclosure for Field Mounting and Panel Mounting
  • Three sets of preloaded pH buffer standards (NIST, US and DIN) cover most commonly used pH calibration practices
  • Supports many temperature compensation elements and sensor types

Unique Human Machine Interface

The PH450 has a high-resolution, simple touchscreen menu structure with five language options, so information is clearly visible and easily accessible to the operator. Simply select the language of choice and on-screen instructions assure that the best configuration for the application is obtained.

Ideal for Ultrapure Water Applications

The PH450 offers self-diagnostics and process temperature compensation to provide accurate pH measurements in high purity water. One of these temperature compensation methods, the NEN6411 algorithm, takes into account the dissociation of water in strong acid and alkaline solutions, which is especially useful for pH measurement in Pure and Ultrapure water as found in Power Generation Water Chemistry.

INSTALLATION AND WIRING

3-1. Installation and dimensions
3-1-1. Installation site
The EXAxt 450 converter is weatherproof and  can be installed inside or outside. It should, however, be installed as close as possible to the sensor to avoid long cable runs between sensor and converter. In any case, the cable length should not exceed 50 metres (162 feet). Select an installation site where:
• Mechanical vibrations and shocks are negligible
• No relay/power switches are in the direct environment
• Access is possible to the cable glands (see figure 3-1)
• The converter is not mounted in direct sunlight or severe weather conditions
• Maintenance procedures are possible (avoiding corrosive environments)
The ambient temperature and humidity of  the installation environment must be within
the limits of the instrument specifications. (See chapter 2).

3-1-2. Mounting methods

Refer to figures 3-2 and 3-3. Note that the EXAxt converter has universal mounting capabilities:
• Panel mounting using optional brackets
• Surface mounting on a plate (using bolts from the back)
• Wall mounting on a bracket (for example, on a solid wall)
• Pipe mounting using a bracket on a horizontal or vertical pipe Size nominal 50A

YOKOGAWA PH450 Product Manual

 

Manual & Datasheet

#FileDescriptionDate addedAdded byFile sizeDownloads
1 pdf YOKOGAWA PH45012/01/2018 16:37admin3 MB131

Please upload your inquiry list

YOKOGAWA PH450

Buy YOKOGAWA PH450 parts, 100% original and Made in Germany.

Inquiry about this YOKOGAWA PH450 series items

Inquiry about YOKOGAWA PH450 Items